基于热态叶型的小轮毂比弯掠叶片结构保形设计与优化

发展了一种保持且基于气动设计给定的热态叶型的冷态叶型迭代解算方法,并将其融入叶片罩量调节的优化设计,其中在热态叶型的基础上调节罩量,针对冷态叶型计算变形与应力等,变形后的叶片逼近热态叶型,尽可能减小了对热态叶型气动特性的影响.实现了冷态叶型迭代求解与罩量调节中结构有限元网格的自动更新,并基于iSIGHT优化平台,建立了叶片罩量调节多目标优化设计的自动化分析流程,并以一小轮毂比弯掠风扇叶片罩量调节为例,考查了罩量调节中考虑轮盘与否对优化设计结果的影响.计算分析实例表明:所发展的方法可在保持热态叶型的前提下使叶片最大应力和最大变形分别下降了10.6%和46%.      

轴流压气机静子角区分离流动的DDES数值研究

为进一步加深对压气机静子角区分离流动非定常性和湍流特性的认识,以某台用于低速模拟的多级低速轴流压气机的第3级改型静子为研究对象,采用延迟脱落涡模拟(DDES)方法进行详细的数值研究。结果表明:压气机静子角区分离流动受到叶片几何参数和来流条件的综合影响;通道涡是引起静子角区分离的主要涡系结构,其发展过程伴随着大小尺度发簪涡的交替出现;通道涡、发簪涡和尾迹脱落涡的相互作用是引起静子角区分离流动非定常性的主要来源;静子角区存在高度各向异性和能量反传的湍流特征;角区分离区的频率幅值强于主流区,振幅较大的区域位于500 Hz以下的低频区。      

Experimental study on NOx emission correlation of fuel staged combustion in a LPP combustor at high pressure based on NO-chemiluminescence

Experimental investigations on NO_x emissions of a single-cup, Lean Premixed Prevaporized (LPP), module combustor were carried out at elevated inlet temperature and pressure up to 810 K and 2.0 MPa, close to the real operating conditions of aero-engine combustors. This LPP combustor adopts centrally staged fuel injections which could produce separated stratified swirling spray flame. In the NO_x emissions measurements, the ranges of dome equivalence ratio and fuel stage ratio were from 0.55 to 0.58 and 8% to 24%, respectively. The optical diagnosis on separated stratified swirling spray flame were carried out with fuel stage ratio changing from 15% to 30%. Therefore, NO* and OH* chemiluminescence images were obtained. The results show that NO_x emissions increase with the increase of the fuel stage ratio. And from the chemiluminescence images, the main flame and pilot flame are found weakly coupled. The pilot flame plays a significant role in NO_x emission production because of its higher adiabatic flame temperature. Based on the results of chemiluminescence optical tests, a new NO_x emission prediction model is proposed based on the Lefebvre’s single flame model. The estimate of local equivalence ratio of the pilot stage’s non-premixed flame is modified considering the characteristics of spray combustion, and a “PLUS” emission prediction model suitable for separated stratified swirling spray flame is obtained. Compared to the experimental data, the “PLUS” model exhibits a good prediction in a range of ±13% of deviation.     

Lock-in phenomenon of tip clearance flow and its influence on aerodynamic damping under specified vibration on an axial transonic compressor rotor

In this study, the lock-in phenomenon of Tip Clearance Flow(TCF) instabilities and their relationship to blade vibration are investigated numerically on an axial transonic rotor with a large tip clearance. The capabilities of simulating instability flow and lock-in phenomenon are verified on a transonic rotor and a NACA0012 airfoil by comparing with the test data, respectively.The lock-in phenomenon is first numerically confirmed that may occur to TCF instabilities when its frequency is close to...     

带支板轴对称弯曲管道的流动特性

以一种带支板的轴对称弯曲管道为研究对象,通过试验与仿真手段,获得了有无支板时的内部流场特性,并探讨了尾迹流特性以及出口马赫数的影响规律.研究结果表明:试验数据与仿真结果在趋势和数值上均吻合良好.气流在弯曲管道中先减速后加速,并在"一弯"中心体侧和"二弯"外罩侧附近形成局部低压区;支板对弯曲管道的内部流动结构影响显著,诱导了尾迹流和旋涡的形成,尾迹区附近不同径向位置处的总压分布规律呈现明显差异;此外,随出口马赫数的增大,弯曲管道壁面沿程静压和出口总压恢复系数均降低,而"一弯"和"二弯"处的逆压力梯度增大,故发生边界层分离的风险性增大.      

航空发动机中的干摩擦阻尼器及其设计技术研究进展

总结了航空发动机中的典型干摩擦阻尼器的结构形式及其工作原理,并给出了干摩擦模型以及接触运动模型的简化方法以及不同简化模型的优缺点和适用范围.分析了干摩擦阻尼系统响应分析的各种方法的特点,重点论述了近年来发展较为迅速的基于时频转换算法的高阶谐波平衡法的基本思想,并介绍了在进行时频转换分析过程中的弧长延拓法等关键技术.最后,论述了航空发动机中干摩擦阻尼器的设计和发展所面临的困难和未来的发展方向.      

干摩擦阻尼器对宽频多阶次激励减振效果分析

在对干摩擦阻尼非线性系统响应求解的高阶谐波平衡法、摩擦力时域求解的时间推进法以及时频转换（AFT）法中的关键技术进行介绍的基础上,采用将时频转换法与高阶谐波平衡法相结合的方法对典型航空发动机叶片缘板阻尼器宽频多阶次激励的减振效果进行计算与分析.通过与直接积分法获得的结果进行对比,表明该方法具有较高的计算精度,且计算效率远远高于直接积分法.对比了保留不同谐波阶次时的计算结果,说明对航空发动机中宽频多阶次激励下的干摩擦阻尼系统进行分析计算时需要保留非线性力的高阶谐波成分,才能获得准确的结算结果.干摩擦阻尼器对于不同频率成分激起的共振峰值的最优正压力值不同,实际中应针对激振频率带宽及具体的减振需求,对阻尼器的设计参数进行优化设计,使得系统在整个工作频带上振动响应最小.      

基于数字图像相关方法微裂纹萌生试验研究

为了进一步研究疲劳裂纹在萌生阶段的特点,本文结合数字图像相关方法 (Digital Image Correlation Method,DIC)设计并组建了配合液压疲劳试验机加载的原位观测系统。同时针对DIC测量方法中的关键技术进行研究,分别提出了一种可应用于视场宽度2mm下DIC计算的微小散斑制备方法,以及空间调节方法以提高试验可靠性。最后应用该系统开展针对航空发动机火焰筒材料GH536的微裂纹自然萌生试验。通过采取两种不同的DIC分析策略,分别获得疲劳过程中的总应变幅以及最大累积塑性应变的演化规律。结果表明总应变幅演化可确定自然萌生裂纹位置,最小可识别50μm裂纹;最大累积塑性应变分析可得萌生寿命占比约85%,并在裂纹出现后塑性应变急剧增加。     

Inverted decoupling and LMI-based controller design for a turboprop engine with actuator dynamics

The main objective of the turboprop engine control system is to ensure propeller absorbed power at a constant propeller speed by controlling fuel flow and blade angle. Since each input variable affects the selected output variables, there exist strong interactions between different control loops of a Two-Spool TurboProp Engine (TSTPE). Inverted decoupling is used to decouple the interactions and decompose the TSTPE into two independent single-input single-output systems. The multi-variable PI controller and two single-variable PI controllers are designed for the TSTPE with actuator dynamics based on Linear Matrix Inequality (LMI), respectively, which is derived from static output feedback and pole placement condition. The step responses show that due to the difference in the response times of the selected output variables, it is difficult to design an appropriate multi-variable PI controller. The designed single-variable PI controllers are tested on the TSTPE integrated model to illustrate the effectiveness of the proposed method, that is, the interactions are first decoupled and then the controllers are designed, and the resulting simulated responses show that compared with the controller designed without actuator dynamics, the gas-generator shaft speed and power turbine shaft speed can better track their respective commands under the action of the controller designed with actuator dynamics.     

Research on vibration suppression of a mistuned blisk by a piezoelectric network

The work aims to provide a further investigation of the dynamic characteristics of an integral bladed disk(also called ‘blisk') with a Parallel Piezoelectric Network(PPN). The PPN is constructed by parallelly interconnecting the piezoelectric patches distributed in the blisk. Two kinds of PPN are considered, namely mono-periodic PPN and bi-periodic PPN. The former has a piezoelectric patch in each sector, and the later has one patch every few sectors. The vibration suppression performance of both kinds of PPN has been studied through modal analysis, forced response analysis, and statistical analysis. The research results turn out that the PPN will only affect mechanical frequencies near the electrical frequency clusters slightly, and the bi-periodic PPN will make the nodal diameter spectrum of the modes more complex, but the amplitude corresponding to the new nodal diameter component is much smaller than that of the nodal diameter component corresponding to the mono-periodic system. The mechanical coupling between the blades and the disk plays an important role in the damping effect of the PPN, and it should be paid attention to in applications. The mono-periodic PPN can effectively suppress the amplitude magnification of the forced response induced by the mistuning of the blisk; meanwhile, it can mitigate the vibration localization of the mistuned electromechanical system. If piezoelectric patches are set only in part of the sectors, the bi-periodic PPN still has a vibration suppression ability, but the effect is related to the number and spatial distribution of the piezoelectric patches.